Comment posted Forgot Salt In Water Softener,now There Is Mold, What Do I Do? by bert2730.

How much mold is there? Turn the bypass valve so none of the cleaners will get into your pipes. If there is enough to vacuum out get out what you can. Use bleach, just spray it in there 10:1 concentration is plenty, it will kill all of the mold. Suck all of that water out too. Once it looks clean you will probably need to pour some undilluted bleach in the mixing reservoir. Not where you put the salt, the other tube that probably has a cap on it, where the water runs into when it recharges. Then set it to recharge now and let that bleach solution run into the softener itself, the cylinder that looks like an air tank. If you still have the documentation that came with the softener it will also tell you how to disinfect your softener and how much bleach to run in the recharge cycle. Once it is clean and rinsed out, fill it with salt and close the bypass valve. I wouldn’t use soap, you might never get it all out and you’ll get suds from your inside tap water.

Recent comments by bert2730

• Water Heater Issues……..can U Help?
  My first question is, what type heater do you have, gas or electric? Is this the first time you have ever drained the tank? What type of pipes are in your house? Do you have a filter upstream of the heater? Calcium is a byproduct of heating water. The minerals in water settle at the bottom, and should be drained out about 4 times a year. Whether you have gas, electric, tank or tankless, calcium is still a problem. If you are considering a switch from a tank type heater, to a tankless unit, make sure you read, and UNDERSTAND ALL THE MANUFACTURERS RECOMENDATIONS, because if you don’t comply with their instructions, you can possibly do some serious damage to the heater, and your house. The gas models especially need to be installed exactly as the manufacturer says, or damage to the unit, or even a fire can be caused, due to the increased amount of gas required, and the flue pipe needing to be replaced. It isn’t just a simple swap out, as some people think. I have removed more units than I have installed, because after researching the problem, all the units I removed, had been installed, without regard for the manufacturers recommendations. Most of the time it is an undersized gasline, but sometimes the flue pipe was not changed out, and after pricing the suggested flue pipe, the customers went back to a tank model. If you are thinking of this option, call a professional, and make sure he has done this type of installation, before letting him or her do the job. Good luck to you!
• Water Heater Issues……..can U Help?
  If it’s clogged with sediment then maybe most of your tank is and it’s just eating the electricity to keep the sediment hot get a new water heater
• Water Heater Issues……..can U Help?
  Based on the description of the problem and if the unit itself is older I would consider a replacement. If you look at all the sludge in the bottom that is accumulated you must keep in mind that stuff is coming out in your water when you shower, wash bathe etc. Also they are find now that in tank models bacteria such as Legionaires Disease and others can thrive in a dirty tank that sits for long periods. Not Good!
  I have a tankless water heater in my home and it is the best thing ever. It provides endless hot water so you can shower all day if you want and it never runs out. My electric bill went down about 35 dollars a month also as it only turns on when you activate hot water. A tank model turns off and on all day even if you don’t use it. The water is also safer as I indicated as it is not stored and heats as you need it.
  I did a lot of research and the largest selling unit and one that I use is the Titan Tankless N-120 Water Heater. They invented it and have been in business 20 years.
  All of the information on the unit and helpful things to help you decide are on their site at http://www.titantankless.com
  Please be careful about gas models as they are DANGEROUS!
  I would stick with electric.
• Water Heater Issues……..can U Help?
  Replace the hot water heater, it’s done. There’s 3 to 4 inches
  built up on the burner plate, if you did clean it off the steel has been sacrificed.
  So how’s your harvick 29 car doing, yea mark martin is washed, NOT.
• Replacing Element In Electric Water Heater.?
  BUT is the wire feeding the htr lg enuf to handle the larger load????????????????????

powered by SEO Super Comments

Related posts:

1. When To Refill Water Softener With Salt?
2. Water Softener, Which One Is Good, With Or Without Salt?
3. How Do I Clear A Salt Bridge From My Water Softener?
4. Water Softener Salt Tank Has Brown Water In The Bottom?
5. Does Having A Low Salt Level Change The Effectiveness Of Water Softener?